A Randomized Controlled Trial Comparing Digitally Fabricated and Conventional Stabilizing Splints in the Management of Temporomandibular Disorders
A Randomized Controlled Trial Comparing Digitally Fabricated and Conventional Stabilizing Splints in the Management of Temporomandibular Disorders
This randomized controlled trial aims to compare the clinical effectiveness of digitally fabricated and conventionally fabricated maxillary stabilization splints in patients diagnosed with Temporomandibular Disorders (TMD) according to Diagnostic Criteria for Temporomandibular Disorders (DC/TMD).
Participants will be randomly allocated in a 1:1 ratio to receive either a Digitally fabricated splint produced using computer-aided design and three-dimensional printing technology or a conventionally fabricated splint using standard impression and laboratory techniques.
The primary outcome is Change in Pain Intensity measured using the Characteristic Pain Intensity component of the Graded Chronic Pain Scale (GCPS), 0-100 scale. Higher scores indicate greater pain severity from baseline to 3 months as primary end point.
Secondary outcomes include change in pain-related disability assessed using the Graded Chronic Pain Scale (GCPS) disability score, change in maximum mouth opening measured in millimeters (mm), change in jaw functional limitation assessed using the Jaw Functional Limitation Scale (JFLS), resolution of temporomandibular joint (TMJ) clicking (present/absent), change in oral health-related quality of life assessed using the Oral Health Impact Profile-14 (OHIP-14), and compliance with splint use measured as average nightly wear time (hours per night).
Assessments will be conducted at baseline and 3 months post-intervention. Outcome assessment will be performed by a blinded examiner.
This study is a parallel-group randomized controlled clinical trial designed to evaluate the effect of fabrication technique on the clinical performance of stabilization splints in patients with temporomandibular disorders (TMD). Eligible participants will be diagnosed according to Diagnostic Criteria for Temporomandibular Disorders (DC/TMD) Axis I criteria. Following informed consent, participants will be randomly assigned in a 1:1 ratio to either the digitally fabricated splint group or the conventionally fabricated splint group using a computer-generated randomization sequence. Allocation concealment will be ensured by sequentially generated numbered, opaque, sealed envelopes prepared by an independent investigator.
For the digital workflow, maxillary and mandibular arches will be captured using an intra oral scanner. Splints will be designed using computer-aided design software and fabricated using additive manufacturing (three-dimensional printing) with biocompatible resin materials via digital light processing (DLP) technology. Post-processing will include cleaning and light curing according to standardized protocols.
For the conventional workflow, impressions will be obtained using elastomeric materials, followed by cast fabrication and articulation. Stabilization splints will be fabricated using heat-cured acrylic resin according to standardized laboratory procedures.
To ensure comparability between groups, splint design parameters will be standardized. All appliances will be maxillary full-coverage stabilization splints with even and simultaneous bilateral contacts in centric relation and canine-guided occlusion during excursive movements. Splint thickness will be standardized (approximately 2-3 mm), and all appliances will be adjusted intraorally at delivery to achieve uniform occlusal contacts.
Participants will be instructed to wear the splints nightly for a minimum of 8 hours. Clinical evaluations will be conducted at baseline and 3 months post-intervention. Outcome assessment will be performed by an examiner blinded to group allocation.
Data will be analyzed using IBM SPSS Statistics (version 26.0; IBM Corp., Armonk, NY, USA). A two-sided p-value < 0.05 will be considered statistically significant.. Normality will be assessed using the Shapiro-Wilk test. Between-group comparisons will be performed using independent t-tests or Mann-Whitney U tests, as appropriate. Within-group comparisons will be conducted using paired t-tests or Wilcoxon signed-rank tests. Repeated measures will be analyzed using repeated measures ANOVA or mixed-effects models.
This study is designed to isolate the effect of fabrication technique by controlling splint design variables while employing clinically relevant material systems, thereby providing evidence on the comparative effectiveness of digitally fabricated and conventionally fabricated stabilization splints in the management of temporomandibular disorders.
Inclusion Criteria
Exclusion Criteria